Tmsystems Project MIX818 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Multimédia Tmsystems Project MIX818. t&mSystems Project MIX818 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 17
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
PROJECTMIX818
OPERATION MANUAL
ZONE SELECT
OUTPUT LEVEL
FUNCTION
PAGE ALL
ENTER
BGM ALL
ESC
POWER
MONITOR
SOURCE UP SOURCE DOWN
PAGE BUSYMIC1 PRIORITY
ZONE 1
SOURCE UP SOURCE DOWN
PAGE BUSYMIC1 PRIORIT Y
ZONE 8
SOURCE UP SOURCE DOWN
PAGE BUSYMIC1 PRIORITY
ZONE 2
SOURCE UP SOURCE DOWN
PAGE BUSY MIC1 PRIORITY
ZONE 3
SOURCE UP SOURCE DOWN
PAGE BUSY MIC1 PRIORITY
ZONE 4
SOURCE UP SOURCE DOWN
PAGE BUSY MIC1 PRIORITY
ZONE 5
SOURCE UP SOURCE DOWN
PAGE BUSYMIC1 PRIORITY
ZONE 6
SOURCE UP SOURCE DOWN
PAGE BUSY MIC1 PRIORITY
ZONE 7
PROJECTMIX818
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
MIC 1
MUSIC
MASTER
EMERGENCY
Zobrazit stránku 0
1 2 3 4 5 6 ... 16 17

Shrnutí obsahu

Strany 1 - OPERATION MANUAL

Please follow the instructions in this manual to obtain the optimum results from this unit.We also recommend that you keep this manual handy for futur

Strany 2 - SAFETY PRECAUTIONS

The Zone LF Bassof the Zone Outputcan be controlledby adjusting the LFBass Level Control.This Level Controlwill provide adjustment of the 100Hz Au

Strany 3

The System Line Source Input Signal Levelscan be adjusted from 190mV to 200mV usingthe Line Source Input Gain control. This willenable th

Strany 4 - CONTENTS

8 1. RS485 B 2. RS485 A 3. GND 4. + 24V (OUT) 5. GND 6. + 24V (OUT) 7. MIC IN + 8, MIC IN-19. Paging MIC Gain20. MIC1 InputThe balanced

Strany 5 - 1. INTRODUCTION

Status Data To Paging ConsoleInquiry Data To Remote Wall Plate hA 1 E Matrix address code zone data AM AA: data head 1 E: Zone status feedback

Strany 6 - FRONT PANEL LAYOUT

AA 21 line input volume AM AA: data head 21 : feedback data from wall plate to Matrix line input: source input 01 : line 1 02 :

Strany 7

6. CONNECTION DIAGRAMRemote control panclsMaster matrix8 remote control panelExtension matrix 18 remote control panelExtension matrix 28 remote contro

Strany 8 - 3. REAR PANEL LAYOUT

12There are 4 address codes on both remote the paging console and the extension keypad which are used to identify these. Only one address code swit

Strany 10 - Level for the Zone.This

Be sure to read the instructions in this section carefully before use. Make sure to observe the instructions in this manual as the conventions of s

Strany 11 - REAR PANEL LAYOUT

An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated inthe electrical installation of the building.W

Strany 12

CONTENTS1.INTRODUCTION...12.FRONT PANEL LAYOUT...

Strany 13

1. INTRODUCTION Select Source Zone LED Display Monitor Zone Select Page Busy MIC Priority Indicator MIC Priority Button M

Strany 14 - 5. SPECIFICATIONS

1. Source Select2. Zone LED Display3. Page BusyThe source select button (1) is used to select thesource for the zone. Each zone has a separatesou

Strany 15 - 6. CONNECTION DIAGRAM

9. Monitor ZONE SELECTNote:11. Monitor Zone Output LevelThe ZONE SELECT button (9) is used to selectone of the 8 zones to be monitored.Pressing thezo

Strany 16 - 7.CONNECTION AND SETTING

-+dBGAINHFLFPAGEGAIN-10+10dB-10+10dBLF HFMICROPHONE 1 EXTENSION LINKGAIN-8 +8dB-8 +8dBdBOUTPUT -+dBGAINHFLFPAGEGAIN-10+10dB-10+10dB-+dBZONE 8 GA

Strany 17

Each zone can havea remote line levelsource connected. The remote source input connector is shown here.6. Remote Source2. EVAC / Fire System Interf

Komentáře k této Příručce

Žádné komentáře